“[Pack of 50] DeWalt 7412SD1-PWR 3/8 X 2-3/4 Power-Stud Plus SD1 Wedge Expansion Anchor” has been added to your cart.
View cart
Showing 1–40 of 173 resultsSorted by popularity
-
$1.13
Features:
- MAB15Z anchors mudsill to concrete block, poured walls or slab foundations
- Nominal sill size: 2×4, 2×6, 2×8, 2×10, 2×12
- Made from 18-gauge steel
- ZMAX galvanization offers extra corrosion resistance for exterior and treated-wood applications
-
This item has been DISCONTINUED.
-
This item has been DISCONTINUED.
-
$52.79
Features
- SET3G22-N is ICC-ES ESR-4057 approved for post-installed anchoring and rebar splice design
- Includes mixing nozzle and extension for simplified installation
- Low-odor formula, approved for potable water applications
- Compatible with wire brush cleaning or vacuum-drill systems without extra hole cleaning
-
$0.43
Features:
- Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
- Positive-set marking system indicates when anchor is properly set
- Zinc-plated carbon steel
- Length: 2 in.
- Drill bit diameter: 5/8 in.
Minimum order quantity: 50
Order in multiples of: 50
-
$15.18
Features
- THDB25178HC20 is tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Reuse of the anchor will not achieve listed loads and is not recommended
-
- This item has been DISCONTINUED.- SEE ET3G22-N FOR UPDATED MODEL
-
$29.95
Features
- PFM1411020 is designed for standard ANSI tolerance drill bits
- Patented thread design offers low installation torque
- Tough threads for tapping high strength concrete
- Ratchet teeth on underside of hex washer head lock against the fixture
- Can be installed closer to the edge than traditional expansion anchors
-
$1.85
Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
-
$39.46
Features
- PFM1411380 is designed for standard ANSI tolerance drill bits
- Patented thread design offers low installation torque
- Tough threads for tapping high strength concrete
- Ratchet teeth on underside of hex washer head lock against the fixture
- Can be installed closer to the edge than traditional expansion anchors
-
$5.53
Features:
- STB2-75812 offers a chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
$39.90
Features
- PFM1411100 is designed for standard ANSI tolerance drill bits
- Patented thread design offers low installation torque
- Tough threads for tapping high strength concrete
- Ratchet teeth on underside of hex washer head lock against the fixture
- Can be installed closer to the edge than traditional expansion anchors
-
$71.43
Features:
- Manual dispensing tool
- EDT22S features a steel carriage and is engineered for high-volume, continuous use
- The tool can be easily convert from dispensing a 22 oz. 1:1 ratio cartridge to a 16.5 oz. 2:1 ratio cartridge
- For 22 oz. adhesive cartridges
-
$87.26
Features
- THDB62100WH is tested in accordance with ACI 355.2 and AC193
- For added convenience, a 1/2″ socket adapter and (2) T-drive bits are included in each box
- Washer head allows screw anchor applications incompatible with a hex head
-
$4.95
Features
- THD50600HMGF1 is tested in accordance with ACI 355.2, AC193 and AC106
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
$92.31
Features
- THD50800H is tested in accordance with ACI 355.2, AC193 and AC106
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
$26.60
Features:
- An 18-element mixing nozzle for use with 22 oz. and 56 oz. epoxy adhesive cartridges
- EMN22I-RP5 is a one-piece nozzle with integrated nut (separate retaining nut not required)
- Once the epoxy hardens in the nozzle it can be used as a cap to keep the product fresh
- Each nozzle is 14 in. long for use in all depths of holes
- Quantity: 5
-
$28.95
Features
- PFM1411060 is designed for standard ANSI tolerance drill bits
- Patented thread design offers low installation torque
- Tough threads for tapping high strength concrete
- Ratchet teeth on underside of hex washer head lock against the fixture
- Can be installed closer to the edge than traditional expansion anchors
-
$49.43
Features
- THDB62600WH is tested in accordance with ACI 355.2 and AC193
- Qualified for static, wind and seismic loading conditions
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- Washer head allows screw anchor applications incompatible with a hex head
-
6% OFF
$64.92 Original price was: $64.92.$61.02Current price is: $61.02.
Features
- Designed to install using a rotary hammer or hammer drill with standard ANSI drill bits — no special tools required
- THDB37158RH is code listed for cracked and uncracked concrete applications under the 2015, 2012 and 2009 IBC/IRC, per ICC-ES ESR-2713
- FM listed
-
$24.49
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$61.84
Features
- THD37400CS offers superior performance
- Removable design
- Reduced cam-out
- Countersunk head profile
-
$95.38
Features
- THD37500H is tested in accordance with ACI 355.2, AC193 and AC106
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- Reuse of the anchor will not achieve listed loads and is not recommended
-
$28.49
Features
- STB2-37334 has a chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3 1/4″, and lightweight concrete-over-steel deck thickness of 2 1/2″ and 3 1/4″
- Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes
-
$17.29
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$18.58
Features
- CFC free propellant
- Class B2 Flame retardant
- Physiologically harmless when fully cured
- Contains no urea formaldehyde or PCB’s
- Does not rot or deteriorate with age
-
$33.75
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$26.05
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$42.35
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$34.49
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$36.99
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$26.65
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$23.35
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$24.50
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$17.79
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$16.99
Features
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading
-
$22.35
Features
- Structural connections, i.e., bean and column anchorage
- Safety related attachments
- Interior applications / low level corrosion environment
- Tension zone applications, i.e., cable trays and strut, pipe supports, fire sprinklers
- Seismic and wind loading
-
6% OFF
$106.92 Original price was: $106.92.$100.50Current price is: $100.50.
Features
- THD37600H is tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Do not reuse anchor
-
$80.00
Features
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- THD75500H4SS is tested in accordance with ACI355.2, AC193 and AC106
-
$195.69
Features
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- THD50612H4SS is tested in accordance with ACI355.2, AC193 and AC106
