Showing 5001–5040 of 5425 resultsSorted by popularity
-
Standard Shipping
$46.82
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 4×6
-
Standard Shipping
$26.71
Features:
- The nailing pattern allows for nailing to the edges of double 2x’s
- Strap nail slots are countersunk to provide a lower nail head profile
- The slots below the embedment line enable increased front-to-back concrete bond and help to reduce spalling
- Standard strap length: 26-1/8 in.
- Made from 12-gauge steel
-
Free Shipping
$210.59
Features:
- Sized to fit nominal 2x lumber
- Packaged in lightweight cartons
- Length: 150 ft.
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
Standard Shipping
$5.31
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$18.35
Features:
- Provides a positive connection for a post to a wood deck
- Stronger than angled nailing or screw fastening
- Reduces the chance of the post splitting and eliminates nailing into end grain
- Not recommended for non top-supported installations (such as fences or unbraced carports)
- Nominal post size: 6x
-
Free Shipping
$603.93
Features:
- Semi-automatic and fast cycling
- PT-27 is Compatible with Simpson Strong-Tie powder loads and pins
- Fastener length: 1/2? 2-1/2 in. (3 in. washered)
- Fastener type: .300 in. or 8 mm-headed fasteners or 1/4-in.-20 threaded studs
- Load caliber: 0.27 strip loads, brown through red (levels 2?5)
-
Standard Shipping
$4.20
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$20.24
Features:
- SUL = skewed left
- Can accommodate joists skewed 40 to 50 degrees
- Angled nail slots direct nails for proper installation
- Nominal joist size: 2×10 or 2×12
- Made from 16-gauge steel
-
Standard Shipping
$16.04
Features:
- The minimum effective shank length must equal or exceed the sum of the thickness of the attached material and the minimum embedment depth
- Code listed per ICC-ES ESR-2138, Florida FL15730 and LA RR25469
- Compatible with Simpson Strong-Tie powder-actuated tool systems as well as other common tools
- .300-in. head diameter / .157-in. shank diameter
- 1-in. washer
-
Standard Shipping
$2.13
Features:
- Straps are load rated with the correct thickness and number of fasteners, in contrast with field-fabricated straps
- Loads have been increased for wind and seismic forces
- Floor-to-floor clear span application
- For use on the edge of 2x members
- Length: 24 in.
-
Standard Shipping
$20.24
Features:
- SUR = skewed right
- Features obround nail holes on the acute side, allowing nails to be easily installed parallel to the joist
- These hangers cannot be modified but will accommodate a 40 degree to 50 degree skewed joist
- Available with the acute flange turned in to accommodate end-of-wall installation for solid sawn sizes only (SURC or SULC)
- Nominal joist size: 2×10 or 2×12
-
Standard Shipping
$3.05
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$5.59
Features:
- Can be installed filling round holes only, or filling round and triangle holes for maximum values
- Nominal joist size: 2×6
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
Standard Shipping
$2.66
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 4-1/4 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$10.71
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 4×4
-
Standard Shipping
$51.97
Features:
- Manual dispensing tool
- Features a steel carriage for ultimate durability and is engineered for continuous, high-volume use
- Double-gripping plates that help extend tool life
- For SET3G10 adhesive and other 10 oz. single-cartridge adhesives
-
Standard Shipping
$26.20
Features:
- Discontinued
- Designed for nail- or bolt-on applications
- For use in vertical or horizontal applications
- 5/16 in. seat thickness
- Length: 19-3/4 in.
- Made from 12-gauge steel
-
Standard Shipping
$28.56
Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 6×6
-
Standard Shipping
$6.68
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 8-1/2 in.
- Made from mechanically galvanized carbon steel
-
Standard Shipping
$52.89
This item has been DISCONTINUED.
-
Standard Shipping
$1.29
Features:
- A versatile and easy-to-use mending plate for wood-to-wood connections
- These non-structural connectors are ideal for general fix-up work
- Installs without nails; align wood with arrows at joint and hammer plate to embed prongs
- Used for non-structural applications only (not for truss applications)
- Width: 3 in.
-
Standard Shipping
$9.51
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from mechanically galvanized carbon steel
-
Standard Shipping
$1.72
Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 8-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
Standard Shipping
$5.54
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$2.83
Features:
- Helps resist tension forces
- Staggered nail pattern reduces the potential for splitting
- Width: 1-1/4 in.
- Length: 21-5/8 in.
- Made from 16-gauge steel
-
Free Shipping
$266.58
Features:
- Cap-style head countersinks fully into the double top plate to avoid interference with drywall or finish trades
- Wide tolerance on installation angle makes it easy to install the SDWC correctly
- Can be installed from inside the structure, eliminating exterior work on the upper stories and enhancing job safety
- Fastening can be performed before or after exterior sheathing is applied for added flexibility
- Type-17 point for faster starts and easier driving
-
Standard Shipping
$2.59
Features:
- Available with the bend reversed; specify –REV- after the model number, such as HTS16-REV
- Versatile with many lengths offered to fit the specific application
- Straps do not need to be wrapped over the truss to achieve the allowable load
- Length: 16 in.
- Made from 14-gauge steel
-
Standard Shipping
$28.25
Features:
- Cost-effective one-piece design compared to welded hangers
- A full-height joist flange that captures the top chord of the joist to prevent rotation and eliminate the need for web stiffeners
- Available for special order to accommodate sloped and/or skewed members
- Actual joist size: 3-1/2 in. x 14 in.
- Made from 14-gauge steel
-
Standard Shipping
$3.02
Features:
- Available with the bend reversed; specify –REV- after the model number, such as HTS20-REV
- Versatile with many lengths offered to fit the specific application
- Straps do not need to be wrapped over the truss to achieve the allowable load
- Length: 20 in.
- Made from 14-gauge steel
-
Standard Shipping
$0.24
Features:
- Quick installation, no nails required
- Keeps panels even for a level structural plane
- Provides the 1/8-in. space between plywood panels as recommended by the American Plywood Association
- Use the same size sheathing clip as the panel thickness
- Made from 20-gauge steel
-
Standard Shipping
$20.15
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$14.15
Features:
- Suitable for lighter duty holdown applications on single or double 2x posts
- Ties the guardrail post into deck framing
- Stronger and safer than nails, lag screws or bolts
- Ties the deck into the house for a stronger, safer ledger connection
- Helps prevent a common type of deck failure
-
Standard Shipping
$25.46
Features:
- Simpson Strong-Tie Connector nails are the best choice for Simpson Strong-Tie connectors
- Head ID stamp for easy identification
- Smooth shank
- Smooth head
- Length: 1-1/2 in.
-
Standard Shipping
$52.37
Features:
- Eliminates the need to access the floor joists inside the house
- Ties the guardrail post into deck framing
- Stronger and safer than nails, lag screws or bolts
- Ties the deck into the house for a stronger, safer ledger connection
- Helps prevent a common type of deck failure
-
Standard Shipping
$8.29
Features:
- Designed to help resist download forces
- The unique two-level embossment provides added stiffness to the top flange
- Quick installation
- Seat width: 1-9/16 in.
- Height: 9-3/16 in.
-
Standard Shipping
$2.53
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$0.87
Features:
- Great for connecting 2x deck joists on top of a perpendicular beam
- Install in pairs on either side of the rafter/truss/joist to provide resistance to uplift and lateral forces
- Use also for a variety of connections where one member crosses another
- Made from 18-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
Standard Shipping
$7.05
Features:
- Setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-
Standard Shipping
$6.07
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$2.53
Features:
- Straps are load rated with the correct thickness and number of fasteners, in contrast with field-fabricated straps
- Loads have been increased for wind and seismic forces
- Floor-to-floor clear span application
- Length: 24 in.
- Width: 1-1/4 in.
