Showing all 29 resultsSorted by popularity
-
$1.13
Features:
- MAB15Z anchors mudsill to concrete block, poured walls or slab foundations
- Nominal sill size: 2×4, 2×6, 2×8, 2×10, 2×12
- Made from 18-gauge steel
- ZMAX galvanization offers extra corrosion resistance for exterior and treated-wood applications
-
This item has been DISCONTINUED.
-
This item has been DISCONTINUED.
-
$52.79
Features
- SET3G22-N is ICC-ES ESR-4057 approved for post-installed anchoring and rebar splice design
- Includes mixing nozzle and extension for simplified installation
- Low-odor formula, approved for potable water applications
- Compatible with wire brush cleaning or vacuum-drill systems without extra hole cleaning
-
$0.43
Features:
- Faster installation than previous drop-in anchor design sets with 40% fewer hammer hits
- Positive-set marking system indicates when anchor is properly set
- Zinc-plated carbon steel
- Length: 2 in.
- Drill bit diameter: 5/8 in.
Minimum order quantity: 50
Order in multiples of: 50
-
- This item has been DISCONTINUED.- SEE ET3G22-N FOR UPDATED MODEL
-
$1.85
Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
-
$5.53
Features:
- STB2-75812 offers a chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
$71.43
Features:
- Manual dispensing tool
- EDT22S features a steel carriage and is engineered for high-volume, continuous use
- The tool can be easily convert from dispensing a 22 oz. 1:1 ratio cartridge to a 16.5 oz. 2:1 ratio cartridge
- For 22 oz. adhesive cartridges
-
$26.60
Features:
- An 18-element mixing nozzle for use with 22 oz. and 56 oz. epoxy adhesive cartridges
- EMN22I-RP5 is a one-piece nozzle with integrated nut (separate retaining nut not required)
- Once the epoxy hardens in the nozzle it can be used as a cap to keep the product fresh
- Each nozzle is 14 in. long for use in all depths of holes
- Quantity: 5
-
$2.39
Features:
- Anchors mudsill to concrete block, poured walls or slab foundations
- Fill CMU cell with concrete grout first, then place MASB into the grouted cell and adjust into position
- Attach mudsill to anchor only after the concrete grout cures
- Nominal sill size: 2×4, 2×6
- Made from 16-gauge steel
-
$3.37
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 6-1/4 in.
- Made from zinc-plated carbon steel
-
$35.93
Features:
- SDS-plus shank power setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-
$0.96
Features:
- Bolt diameter: 3/8 in.
- Dimensions: 2 in. x 2 in.
- BP 3/8-2 is made from 3/16 in. steel
- Uncoated steel construction
-
$2.24
Features:
- THD50300H is qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$5.31
Features:
- THD50500HMG is qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$4.20
Features:
- THDB62400H is qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$3.05
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$2.66
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 4-1/4 in.
- Made from zinc-plated carbon steel
-
$51.97
Features:
- CDT10S Manual dispensing tool
- Features a steel carriage for ultimate durability and is engineered for continuous, high-volume use
- Double-gripping plates that help extend tool life
- For SET3G10 adhesive and other 10 oz. single-cartridge adhesives
-
$6.68
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 8-1/2 in.
- Made from mechanically galvanized carbon steel
-
This item has been DISCONTINUED.
-
$9.51
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from mechanically galvanized carbon steel
-
$5.54
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$20.15
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
$2.53
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
$7.05
Features:
- Setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-
$6.07
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
$2.20
Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
