Showing 161–195 of 195 resultsSorted by popularity
-
Standard Shipping
$188.31
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$48.86
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Standard fractional sizes, hole size same as anchor size
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Removable — ideal for temporary anchoring or applications where fixtures may need to be moved
- 6-lobe drive reduces driver-bit cam-outs, resulting in easier installation
- Countersunk head allows screw anchor applications incompatible with a hex head
- Available in 1/4″ and 3/8″ diameters
-
$68.15
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Free Shipping
$288.62
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$73.54
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$62.46
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$39.00
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$72.15
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$155.69
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Free Shipping
$244.62
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Free Shipping
$266.92
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$40.37
Features
- Excellent for use in cold weather conditions or applications where fast cure is required.
- superior sustained load performance at elevated temperature.
- can be specified for dry and damp conditions when in-service temperatures range from -40°F (-40°C) to 180°F (82°C).
- Approved for installation with vacuum-drill bit system without further hole cleaning.
- Passed the demanding ICC-ES AC308 adverse-condition tests pertaining to reduced and elevated temperatures and long-term sustained loads.
- Easy hole-cleaning procedure — no power-brushing required.
-
Standard Shipping
$121.41
Features
- superior bond strengths permit ductile solutions in high seismic areas.
- improved sustained load performance at elevated temperature.
- can be specified for all base material conditions when in-service temperatures range from -40°F (-40°C) to 176°F (80°C).
- Recognized per ICC ES AC308
- Approved for installation with multiple vacuum-drill bit systems without further hole cleaning.
- Wire brush hole-cleaning system for conventional blow-brush-blow cleaning method for anchoring.
- With higher bond strengths, ductile solutions can often be achieved with SET-3G in high seismic areas.
- Low-odor formulation.
- no performance difference between water-saturated concrete, water-filled holes, or submerged concrete.
- For use with potable water.
-
Standard Shipping
$111.29
This item has been DISCONTINUED.
-
Standard Shipping
$2.39
Features:
- Anchors mudsill to concrete block, poured walls or slab foundations
- Fill CMU cell with concrete grout first, then place MASB into the grouted cell and adjust into position
- Attach mudsill to anchor only after the concrete grout cures
- Nominal sill size: 2×4, 2×6
- Made from 16-gauge steel
-
Standard Shipping
$4.09
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 6 in.
- Made from mechanically galvanized carbon steel
-
Standard Shipping
$5.29
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$3.37
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 6-1/4 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$35.93
Features:
- SDS-plus shank power setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-
Standard Shipping
$0.96
Features:
- Bolt diameter: 3/8 in.
- Dimensions: 2 in. x 2 in.
- Made from 3/16 in. steel
- Uncoated steel construction
-
Standard Shipping
$2.24
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$5.31
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$4.20
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$3.05
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$2.66
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 4-1/4 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$51.97
Features:
- Manual dispensing tool
- Features a steel carriage for ultimate durability and is engineered for continuous, high-volume use
- Double-gripping plates that help extend tool life
- For SET3G10 adhesive and other 10 oz. single-cartridge adhesives
-
Standard Shipping
$6.68
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 8-1/2 in.
- Made from mechanically galvanized carbon steel
-
Standard Shipping
$52.89
This item has been DISCONTINUED.
-
Standard Shipping
$9.51
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 5/8 in.
- Length: 10 in.
- Made from mechanically galvanized carbon steel
-
Standard Shipping
$5.54
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$20.15
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$2.53
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$7.05
Features:
- Setting tool for DIAB anchors
- For use with Simpson Strong-Tie Drop-In models DIAB50, DIABL50, and DIAB50C
- Sets drop-ins for overhead applications
- Drop-in anchors are sold separately
- Made from carbon steel
-
Standard Shipping
$6.07
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$2.20
Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
