Showing all 17 resultsSorted by popularity
-
Standard Shipping
$4.07Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 20-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
Standard Shipping
$1.85Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
-
Free Shipping
$172.60Features:
- Made of carbon steel wire
- Tangle-free unwinding
- Full case count – 20 rolls
-
Standard Shipping
$1.66Features:
- Embossment feature provides strength at the bend
- Features optional diamond holes of various uplift capacities with min./max. nailing configurations
- Can be installed before or after placement of wall
- Width: 1-1/2 in.
- Length: 7-7/8 in.
-
Special Order Shipping
$367.10TW1525 Max 16ga Regular Steel Tie Wire for MAX RB655 series
-
Standard Shipping
$2.39Features:
- Anchors mudsill to concrete block, poured walls or slab foundations
- Fill CMU cell with concrete grout first, then place MASB into the grouted cell and adjust into position
- Attach mudsill to anchor only after the concrete grout cures
- Nominal sill size: 2×4, 2×6
- Made from 16-gauge steel
-
Standard Shipping
$1.99Features:
- Holds the rafter or truss on both sides for high lateral load resistance
- Used for a variety of connections where one member crosses another
- Can be installed on inside or outside of wall, or both sides
- Can be installed with flanges facing either inward or outward
- Made from 18-gauge steel
-
Standard Shipping
$2.29Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 12-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
Free Shipping
$210.59Features:
- Sized to fit nominal 2x lumber
- Packaged in lightweight cartons
- Length: 150 ft.
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
Standard Shipping
$20.24Features:
- SUL = skewed left
- Can accommodate joists skewed 40 to 50 degrees
- Angled nail slots direct nails for proper installation
- Nominal joist size: 2×10 or 2×12
- Made from 16-gauge steel
-
Standard Shipping
$20.24Features:
- SUR = skewed right
- Features obround nail holes on the acute side, allowing nails to be easily installed parallel to the joist
- These hangers cannot be modified but will accommodate a 40 degree to 50 degree skewed joist
- Available with the acute flange turned in to accommodate end-of-wall installation for solid sawn sizes only (SURC or SULC)
- Nominal joist size: 2×10 or 2×12
-
Standard Shipping
$5.59Features:
- Can be installed filling round holes only, or filling round and triangle holes for maximum values
- Nominal joist size: 2×6
- Made from 16-gauge steel
- Galvanized (G90) for extra corrosion resistance
-
Standard Shipping
$10.71Features:
- Attaches a post to existing concrete for decks, patio covers and other top-supported structures
- Features 1-in. standoff to help prevent rot at post end
- Slotted for adjustability
- Designed for versatility, cost-effectiveness and maximum uplift performance
- Nominal post size: 4×4
-
Standard Shipping
$1.72Features:
- An indented embedment line ensures accurate embedment depth
- Compatible with the Simpson Strong-Tie preassembled TSS snap-in seat
- Load rated for wind and seismic forces
- 8-in. exposed length
- Embed 4 in. into a poured concrete bond beam or grouted block wall
-
Standard Shipping
$2.83Features:
- Helps resist tension forces
- Staggered nail pattern reduces the potential for splitting
- Width: 1-1/4 in.
- Length: 21-5/8 in.
- Made from 16-gauge steel
-
Standard Shipping
$2.20Features:
- Attaches easily to the concrete form for quick installation
- Lays flat on the form board so there is no anchor bolt to finish around
- No labor costs involved in drilling plates and aligning holes
- Flat design eliminates chances of modification in prefabricated walls
- Eliminates the need to notch studs due the anchor bolts being placed where it will interfere
-
Standard Shipping
$13.41Features:
- SUR = skewed right
- Features obround nail holes on the acute side, allowing nails to be easily installed parallel to the joist
- These hangers cannot be modified but will accommodate a 40 degree to 50 degree skewed joist
- Available with the acute flange turned in to accommodate end-of-wall installation for solid sawn sizes only (SURC or SULC)
- Nominal joist size: 2×6 or 2×8
