Showing all 33 resultsSorted by popularity
-
Standard Shipping
$5.53
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$80.00
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$138.54
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$47.92
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$43.19
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$128.54
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$27.69
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$98.69
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$142.00
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$94.62
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$29.62
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$115.92
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$72.00
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$184.77
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$104.15
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$106.85
Features
- THDSS stainless-steel screw anchor available in 1/4″, 5/8″ and 3/4″ diameters, in addition to the 3/8″ and 1/2″ sizes
- Ideal for exterior or corrosive environments
- Less carbon steel, less expansion
- Installs with an impact wrench or by hand tool
- Tested in accordance with ACI355.2, AC193 and AC106
-
Standard Shipping
$54.85
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$40.15
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
$68.15
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$73.54
Features
- Tested in accordance with ACI 355.2, AC193 and AC106
- Qualified for static, wind and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- Standard fractional sizes
- Specialized heat-treating process creates tip hardness for better cutting without compromising the ductility
- No special drill bit required — designed to install using standard-sized ANSI tolerance drill bits
- Hex-washer head requires no separate washer, unless required by code, and provides a clean installed appearance
- Removable — ideal for temporary anchoring (e.g., formwork, bracing) or applications where fixtures may need to be moved
- Reuse of the anchor will not achieve listed loads and is not recommended
-
Standard Shipping
$135.89
Features
- Bit extracts dust while drilling for less dust, fast holes and fast adhesive anchor installation
- Y-cutter carbide design for exact positioning, perfect starting & maximum durability
- Connects directly to DeWalt’s airlock system forming a secure, locking connection between bit and dust extractor
- Part of DEWALT’s complete cordless anchoring solution
-
Standard Shipping
$48.49
Features:
- Diablo Rebar Demon™ SDS-Max 4- Cutter Full Carbide Head Hammer Bit
- Diablo made Dura-Carbide™ withstands impact and high heat applications, dramatically extending life versus standard hammer bits
- Precision Tip delivers stability and accuracy required for fast, precise holes
- Tri-Metal Diffusion Bonding provides heat resistance and prevents breakage of the full-carbide heat for maximum life and productivity
-
Standard Shipping
$32.03
Features:
- Diablo Rebar Demon™ SDS-Max 4- Cutter Full Carbide Head Hammer Bit
- Diablo made Dura-Carbide™ withstands impact and high heat applications, dramatically extending life versus standard hammer bits
- Precision Tip delivers stability and accuracy required for fast, precise holes
- Tri-Metal Diffusion Bonding provides heat resistance and prevents breakage of the full-carbide heat for maximum life and productivity
-
Standard Shipping
$95.10
Features
- 6-cutter bit tip is engineered for drilling in reinforced concrete
- Centering tip features a more aggressive design for faster hole starting
- Central guiding action engineered for more accurate holes
- Aggressive head geometry in primary cutter engineered for use in concrete
- Engineered for reduced vibration
- 31″ usable length
- For use with Rotary Hammers that accept SDS-PLUS shank bits
-
Standard Shipping
$43.67
Features
- 6-cutter bit tip is engineered for drilling in reinforced concrete
- Centering tip features a more aggressive design for faster hole starting
- Central guiding action engineered for more accurate holes
- Aggressive head geometry in primary cutter engineered for use in concrete
- Engineered for reduced vibration
- 16″ usable length
- For use with Rotary Hammers that accept SDS-PLUS shank bits
-
Standard Shipping
$35.81
Features
- 6-cutter bit tip is engineered for drilling in reinforced concrete
- Centering tip features a more aggressive design for faster hole starting
- Central guiding action engineered for more accurate holes
- Aggressive head geometry in primary cutter engineered for use in concrete
- Engineered for reduced vibration
- 8″ usable length
- For use with Rotary Hammers that accept SDS-PLUS shank bits
-
Standard Shipping
$35.70
Features
- Self-centering carbide tip
- Centering tip features a more aggressive design for faster hole starting
- Central guiding action engineered for more accurate holes
- Aggressive head geometry in primary cutter engineered for use in concrete
- Engineered for reduced vibration
- 16″ usable length
- For use with Rotary Hammers that accept SDS-PLUS shank bits
-
Standard Shipping
$29.49
Features
- Self-centering carbide tip
- Centering tip features a more aggressive design for faster hole starting
- Central guiding action engineered for more accurate holes
- Aggressive head geometry in primary cutter engineered for use in concrete
- Engineered for reduced vibration
- 8″ usable length
- For use with Rotary Hammers that accept SDS-PLUS shank bits
-
Standard Shipping
$3.37
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 6-1/4 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$2.66
Features:
- One-piece, wrap-around clip ensures uniform holding capacity
- Threaded end is chamfered for ease of starting nut
- Diameter: 3/4 in.
- Length: 4-1/4 in.
- Made from zinc-plated carbon steel
-
Standard Shipping
$5.54
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
-
Standard Shipping
$20.15
Features:
- Chamfered top designed to prevent mushrooming during installation
- Qualified for static and seismic loading conditions (seismic design categories A through F)
- Suitable for horizontal, vertical and overhead applications
- Qualified for minimum concrete thickness of 3-1/4 in., and lightweight concrete-over-steel deck thickness of 2-1/2 in. and 3-1/4 in.
- Tested per ACI355.2 and AC193
-
Standard Shipping
$6.07
Features:
- Qualified for static and seismic loading conditions
- Thread design undercuts to efficiently transfer the load to the base material
- No special drill bit required; designed to install using standard-sized ANSI tolerance drill bits
- Testing shows the Titen HD installs in concrete with 50% less torque than competitor anchors
- Hex-washer head requires no separate washer and provides a clean installed appearance
